Ask Fakespot Chat questions about this productAlpha
Add detailed feedback
Message
Loading suggested questions
Suggested Questions
Suggested Questions
No suggested questions were found
Pros & Cons
Pros
This is a very reasonably priced enclosure and it’s getting the job done for me. The enclosure is quite large as its meant to accommodate a number of different printers. Dimensions fit most desktop printers, but something to keep in mind is measuremen... Read More
This enclosure is a must for printing with abs or nylon. The heater and temperature control help optimize abs prints, reducing warping. Works well, helps keep heat inside so i can print more exotic materials without having too much warping occurring.
The frame assembles easily and is solid. The printer has a spool and needs to move the bed and gantry so it's understandable.
There is a semi-sealed cutout in the back that the power cord fits through just fine. The usb port allows firmware updates without opening it. The side zipper lets you access the sd card slot to change it out.
The tent is made of fiberglass rods with plastic connectors to assemble. Follow the instructions to complete assembly of your tent. The only bad thing about it is that when it was time to assemble, i had to cut one of the plastic frame pieces about an... Read More
Cons
This is absolutely too small for the neptune 3 to run its table in the y axis properly. Also not wide enough to fit the handheld screen and the x axis connections.
Highlights
Quality
The zippers work well and are high quality.
It has improved ease and quality of prints just by removing variables.
2 stars - barely meets product requirements, may have design issues.
They do not love each other at all and i have to turn off the fan and try to keep the dogs out of my office while printing - ev... Read More
Price
They have this at a relatively good price and it works well, so i would recommend.
Great price for a product that works as well as this has.
I saved for a long time to pay for this printer and it was getting covered with dust and i was worried it would affect the workings of it.
⭐️⭐️ 2 stars - i don't recommend it, it has multiple faults, or a very high price.
Packaging/appearance
The packaging is no-nonsense, as it should be.
The jayo enclosure comes in a relatively small box with the mylar tent, and a number of plastic rods with fittings for them to go together.
Competitiveness
This enclosure is easy to set up and jayo is a trusted brand of mine.
I haven't had one of these previously to compare it to other brands/types.
Creality may be a better bet if you've this machine - but if you've anything smaller you'll be good to go!
This enclosure is virtually identical to the creality ender plus enclosure, but at $36 (current price on amazon) it's $10 cheaper.
Overview
- How are reviewers describing this item?
good, easy, inside, fit and quality. - Our engine has profiled the reviewer patterns and has determined that there is high deception involved.
- Our engine has analyzed and discovered that 15.1% of the reviews are reliable.
- This product had a total of 139 reviews as of our last analysis date on Aug 6 2024.
Helpful InsightsBETA
Posted by a reviewer on Amazon
Trying to print abs without a proper enclosure is a pain in the rear
Posted by a reviewer on Amazon
One thing to keep in mind if your printer sits on a small table or stand you may need to place something on top of the stand as the footprint of this is much large than that of the printer alone
Posted by a reviewer on Amazon
I used a piece of insulation board you can see it in the picture cut to the size of the enclosure footprint
Posted by a reviewer on Amazon
Its juuuuuust too short for the neptune 4 plus all kitted out
Posted by a reviewer on Amazon
Plastic was a little wrinkly to see through
Posted by a reviewer on Amazon
If you will be printing something with fumes or maybe something like abs that can not have any variable in temp then this is what you need
Posted by a reviewer on Amazon
I will need to get a few more for the rest of my 3d printers
Posted by a reviewer on Amazon
I wanted to work with abs filaments on my ender pro so knew i needed an enclosure to maintain the temperatures required for layer adhesion
Review Count History
Price History
Ask Fakespot Chat questions about this productAlpha
Add detailed feedback
Message
Loading suggested questions
Suggested Questions
Suggested Questions
No suggested questions were found